OBD Tools 365 Days Shop
Welcome to OBD365 Sign In or Register
Home - Products - Technical Support - Xprog and Winkfp fixed BMW R56 MCS FRM3 module

Xprog and Winkfp fixed BMW R56 MCS FRM3 module


Xprog and Winkfp fixed BMW R56 MCS FRM3 module


Successfully repaired my dead FRM3 model on my BMW R56, with the MINIMUM cost (xprog and BMW ICOM Winkfp)! Here, i wanna share something useful with you all.xprog

Note: The setup below did work for me, but i’m not sure of yours. You are at your risk.


My model:

2011 BMW R56


Reason for FRM repair:

I disconnected the battery and the DME to change the thermostat and when I put it back together the FRM was dead.


Tool i used:
Except the BMW ICOM A2 emulator plus ISTA+ I had, i also was shopping for xprog v5.55 boxes from


Before this whole ordeal of the junk BMW/MINI FRM dying the only software I used was playing with was Carly for iOS and Dashcommand. But cannot solve issues.


BKGD location:

BKGD is on the HC(S)12 BDM adapter in the attached photo.

Vdd(+5V) = Vcc
GND = GND (do not use the GND that is B0)

I think since we are not using the XCLKS and EXTAL flashing works with or without the BDM adapter.

Xprog m software installation:

I was not able to get this software to work with windows 7 64-bit. I was lucky enough to have an old HDD with windows 7 32-bit.
Before plugging in the xprog hardware go to system properties and change the device installation settings to never install driver software from windows update.

Xprog and FRM fix using Xprog:
Once the software was setup I hooked up the frm to the xprog and tried to make a backup of the existing EPROM via the MCU/MPU -> Freescale 9S12XE -> MC9s12XEQ384_EEE profile. Error partition corrupted. Set the sector to 16. I also made a backup of the existing P-FLASH via the MCU/MPU -> Freescale 9S12XE -> MC9s12XEQ384_P-FLASH profile. I think I got errors the first few times I tried to do this but restarting the program resolved the error.
In the MCU/MPU -> Freescale 9S12XE -> MC9s12XEQ384_EEE profile: erase, blank, open good EEE dump, write, verify, close, new, read.
This took several tries because the read back was still showing as blank.
I removed the BDM adapter and went direct into the xprog box. I also closed the program and reopened it when it kept giving me errors. After I was able to get a good write to the FRM I installed it back into the car and it was working again with a couple of errors (xenon high beam failure and fog light failure).

NCS expert & WINKFP setup for FRM:
In NCS expert I backed up the FRM, changed the VO and VIN, reset the FRM to factory and still had the high beam and fog errors. I proceeded to WINKFP to update the FRM and none of the ZB-numbers for my ECU worked. I updated WINKFP with BMW coding tool and the list of available ZB-numbers changed. After WINKFP was able to update the FRM I went back to NCS Expert and copied the VO from the CAS to the FRM and then set the FRM back to defaults. Everything was fixed. Fired up ISTA+ and cleared fault memory.


Afterwards I hooked the frm back to the xprog and made a backup of the EEE and pflash.

R56 HIGH EKS 35 frm3r pl3 6135 3456395 01 23994322 sw141030 hw07 5324828c5
Internet file:
R56 HIGH EKS 35 frm3r pl3 6135 3456987 01 23994322 sw156033 hw11 5324828r5

According to realoem parts 61353456395 and 61353456987 are Bilaterally exchangeable.





Hopefully this demonstrates to people it’s possible to repair these modules with the minimum cost.

Write a Review
* Rating:
    Please select rating stars.
* Your First & Last Name:
* Your E-Mail Address:
* Review Detail:
*Verification Code:
          No right? Get a new Verification Code
Tell us what you think about this item and share your opinions with other people. Please make sure your review focuses only on this item. All reviews are moderated and will be reviewed within two business days. Inappropriate reviews will not be posted.
After-sales questions and issues: Contact our Customer Service Department. (A customer representative will get back to you).
Please Sign In first if you want to later edit or manage reviews uploaded by yourself.
Bookmark It
Join our community: OBD365 Official Blog OBD365 Twitter OBD365 Facebook OBD365 Youtube OBD365 Google Plus OBD365 Subscribe