Welcome to OBD365 Sign In or Register
Home - Products - Technical Support - 2 Solutions to Replace Ford rear brake pad EPB

2 Solutions to Replace Ford rear brake pad EPB

Description

Two solutions here of Ford EPB replacement for all… One is to replace Ford rear brake pad  with OBDSTAR X300 Pro3, the other is to exchange EPB without obd2 diagnostic tools.

 

Solution I – exchange Ford EPB with Obdstar x300 pro3 key master

 

Obdstar x300 pro3 full package comes with many special functions like Immobiliser, Odometer adjustment , EEPROM/PIC, OBDII, EPB, Oil/Service reset, Battery matching. And It is verified to perform EPB function on Ford without any issue.

obdstar-x300-pro3-volvo-s80-2 obdstar-x300-pro3-volvo-s80-3 obdstar-x300-pro3-volvo-s80-4

 

X300 PRO3 will guide to finish Ford EPB change easily. Just follow the screen instruction to operate

 

Models and functions:

FORD EPB through x300 pro3 obdstar key master

Edge

Brake pump retraction

Brake pump release

Brake pump test

Fusion

Mondeo

Brake pump retraction

Brake pump release

Brake pump test

Taurus

Brake pump retraction

Brake pump release

Brake pump test

 

If you are good at diy car diagnosis, maybe you can try the second solution. NO NEED any cost.

 

 

Solution II – replace EPB without any car diagnostic tools

 

Here is service mode procedure to exchange rear brake pad without diagnostic tool on Ford Fusion 2013.

 

NOTE: EPB service mode is also known as EPB maintenance mode.

Activation
NOTE: Carry out the following service mode activation procedure to deactivate the EPB system.

Set the ignition to ON.

Press and hold the accelerator pedal and place the EPB switch to the RELEASE (downward) position. Continue to hold the accelerator pedal and EPB.

Set the ignition to OFF then set the ignition to ON within 5 seconds. Continue to hold the accelerator pedal and the EPB switch.

 

NOTE 1The EPB system will be deactivated, preventing parking brake application until service has been completed and service (maintenance) mode has been deactivated. The yellow EPB indicator will be illuminated and Maintenance Mode will display on the message center.
NOTE 2When replacing rear brake pads in service (maintenance) mode, the brake caliper piston must be compressed into the caliper housing. The brake caliper piston does not have to be rotated while compressing the piston.
Set the ignition to OFF then release the accelerator pedal and EPB switch.

 

Deactivation
NOTE: Carry out the following service mode deactivation procedure to activate the EPB system.

Set the ignition to ON.

Press and hold the accelerator pedal and place the EPB switch in the APPLY (upward) position. Continue to hold the accelerator pedal and the EPB switch.

Set the ignition to OFF then set the ignition to ON within 5 seconds. Continue to hold the accelerator pedal and the EPB switch.

 

NOTE: The EPB system will fully apply and release the parking brake to guarantee sufficient air gap between the rear brake pads and brake disc.
Release the accelerator pedal and the EPB switch.

Write a Review
* Rating:
    Please select rating stars.
* Your First & Last Name:
* Your E-Mail Address:
* Review Detail:
*Verification Code:
          No right? Get a new Verification Code
 
Tell us what you think about this item and share your opinions with other people. Please make sure your review focuses only on this item. All reviews are moderated and will be reviewed within two business days. Inappropriate reviews will not be posted.
After-sales questions and issues: Contact our Customer Service Department. (A customer representative will get back to you).
Please Sign In first if you want to later edit or manage reviews uploaded by yourself.
Bookmark It
 
Join our community: OBD365 Official Blog OBD365 Twitter OBD365 Facebook OBD365 Youtube OBD365 Google Plus OBD365 Subscribe